Kontron NSC2U IP Network Server User Manual Page 124
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
NSC2U Server—6
Kontron IP Network Server NSC2U
Product Guide, rev. 1.4 December 2009
124
6.2.1 Preparing for the Upgrade
The steps below explain how to prepare to upgrade the BIOS, including how to record
the current BIOS settings and how to obtain the upgrade utility.
Note: In the unlikely event that a BIOS error occurs during the BIOS update process, a
recovery process may need to be followed to return the system to service. See
Section 1.4, “Additional Information and Software” for additional information.
6.2.1.1 Recording the Current BIOS Settings
1. Boot the computer and press <F2> when you see the message:
Press <F2> Key if you want to run SETUP
2. Write down the current settings in the BIOS Setup program.
Note: Do not skip step 2. You will need these settings to configure your computer at the end
of the procedure.
6.2.1.2 Obtaining the Upgrade
Download the BIOS image file to a temporary folder on your hard drive. See
Section 1.4, “Additional Information and Software” for additional information.
Note: Review the instructions and release notes that are provided in the readme file
distributed with the BIOS image file before attempting a BIOS upgrade. The release
notes contain critical information regarding jumper settings, specific fixes, or other
information to complete the upgrade.
6.2.2 Updating the BIOS
Follow the instructions in the readme file that came with the BIOS upgrade. When the
update completes, remove the bootable media from which you performed the upgrade.
Note: Do not power down the system during the BIOS update process! The system will reset
automatically when the BIOS update process is completed.
Note: You may encounter a CMOS Checksum error or other problem after reboot. If this
happens, shut down the system and boot it again. CMOS checksum errors require that
you enter Setup, check your settings, save your settings, and exit Setup.
6.3 Clearing the CMOS
If you are not able to access the BIOS setup screens, the CMOS Clear jumper will need
to be used to reset the configuration RAM. The CMOS clear jumper (J1D3) is shown in
Figure 17, “Recovery Jumper Blocks (J1D1, J1D2, J1D3)” on page 33.
1. Power down the system and disconnect the power cord.
2. Open the server. See Section 3.2.1, “Removing the Chassis Cover” for instructions.
3. Move jumper (J1D3) from the normal operation position, CMOS Clear by BMC, at
pins 1 and 2 to the CMOS Clear Force Erase position, covering pins 2 and 3.
4. Wait five seconds.
5. Move the jumper (J1D3) back to the default position (pins 1-2).
6. Close the server chassis. See Section 3.2.2, “Installing the Chassis Cover” for
instructions.
7. Reconnect the power and power up the system.
- Product Guide 1
- Rev. 1.4 1
- Legal Lines and Disclaimers 2
- Contents 3
- NSC2U Server—Contents 4
- Revision History 7
- NSC2U Server—Revision History 8
- 1 Introduction 9
- 1.3 Product Accessories 10
- Introduction—NSC2U Server 11
- 2Features 12
- 2.1 Server Components 14
- 2.2 NSC2U Server Back Panel 15
- 2.3 NSC2U Server Front Panel 15
- TS000112 17
- 2.5.1 SFP Board Features 18
- Features—NSC2U Server 19
- 2.9 Power Supply 21
- 2.10 System Cooling 21
- 2.10.3 PCI Cooling Area 22
- 2.10.5 Fan Speed Control 23
- 2.10.6 Cooling Summary 23
- 2.11 Hardware Requirements 24
- 3.1 Before You Begin 25
- TS000543 26
- TS000272 27
- TS000544 28
- TS000274 29
- TS000219 30
- AF000810 30
- TS000275 31
- AC PS DC PS 32
- 3.4.1.1 Configuration Jumpers 33
- 3.4.1.2 BIOS Select Jumper 33
- 3.4.2.1 Memory RASUM Features 36
- 3.4.2.2 Supported Memory 36
- TS000300 40
- 3.4.3 Installing DIMMs 41
- Branch 0 42
- Branch 1 42
- 3.4.5.2 Removing a Processor 44
- AF000768 45
- AF000770 46
- AF000771 46
- AF000772 47
- 4.1 Before You Begin 50
- 4.2.1 Riser Card Options 52
- TS000545 53
- TS000280 54
- Full-height Add-in Cards 55
- TS000546 56
- 4.4 Installing Intel 57
- Remote Management Modules 57
- GCM3 ModuleRMM Module 58
- TS000320 59
- TS000319 60
- TS000550 61
- TS000551 62
- TS000552 63
- TS000328 64
- TS000327 64
- TS000329 65
- TS000511 66
- TS000512 67
- TS000513 68
- TS000514 69
- TS000515 70
- TS000516 71
- TS000517 72
- TS000518 73
- TS000519 74
- Figure 59 75
- TS000521 76
- TS000522 77
- TS000523 78
- TS000524 79
- TS000525 80
- TS000526 80
- TS000527 81
- TS000528 82
- TS000529 83
- TS000530 84
- 4.6.4 Re-assemble the System 85
- TS000532 86
- TS000533 87
- TS000534 88
- TS000535 89
- TS000536 90
- TS000502 91
- TS000503 92
- TS000284 93
- TS000301 94
- TS000302 94
- TS000303 95
- TS000554 96
- TS000555 97
- 5.1 Before You Begin 98
- TS000556 99
- 5.2.1 Removing the CPU Fans 100
- 5.2.2 Replacing the CPU Fans 101
- NSC2U Server—5 102
- TS000560 103
- TS000562 105
- TS000564 107
- TS000565 108
- TS000566 109
- Backplane Board 110
- TS000313 111
- Assembly 112
- TS000316 113
- TS000568 115
- TS000569 116
- TS000570 118
- TS000537 119
- TS000308 121
- 6 Server Utilities 122
- 6.2 Upgrading the BIOS 123
- 6.2.1.2 Obtaining the Upgrade 124
- 6.3 Clearing the CMOS 124
- 6.4 Clearing the Password 125
- 7 Troubleshooting 126
- NSC2U Server—7 128
- 7.5 LED Information 131
- 7.6 BIOS Error Messages 132
- 7.6.1 BIOS POST Beep Codes 133
- 8 Warranty 135
- NSC2U Server—8 136
- A.1 Emissions Disclaimer 137
- A.2 Intended Uses 137
- NSC2U Server—A 138
- A.3 Safety Cautions 139
- Wichtige Sicherheitshinweise 140
- Consignes de sécurité 142
- Information en 144
- B.2.1 FCC (USA) 148
- B.2.4 VCCI (Japan) 149
- B.2.5 BSMI (Taiwan) 149
- NSC2U Server—B 150
- Appendix C: Getting Help 151
- NSC2U Server—C 152
Related products and manuals for Computer hardware Kontron NSC2U IP Network Server
(103 pages)
(49 pages)Rockwell Automation 2711E-NKSW1 Replacement Keyswitch Assembly manuals
Owner’s manuals and user’s guides for Equipment Rockwell Automation 2711E-NKSW1 Replacement Keyswitch Assembly.
We providing 1 pdf manuals Rockwell Automation 2711E-NKSW1 Replacement Keyswitch Assembly for download free by document types: User Manual
Comments to this Manuals