Kontron AT8901M CLI User Manual Page 35
- Page / 313
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
AT8901M Using the Command-Line Interface
Page 1 - 9 AT8901M CLI Reference Manual
1.6 Using CLI Help
Enter a question mark (?) at the command prompt to display the commands available in
the current mode.
(switch) >?
enable Enter into user privilege mode.
help Display help for various special keys.
logout Exit this session. Any unsaved changes are lost.
ping Send ICMP echo packets to a specified IP
address.
quit Exit this session. Any unsaved changes are lost.
show Display Switch Options and Settings.
telnet Telnet to a remote host.
Enter a question mark (?) after each word you enter to display available command
keywords or parameters.
(switch) #network ?
javamode Enable/Disable.
mgmt_vlan Configure the Management VLAN ID of the switch.
parms Configure Network Parameters of the router.
protocol Select DHCP, BootP, or None as the network
config
protocol.
If the help output shows a parameter in angle brackets, you must replace the parameter
with a value.
(switch) #network parms ?
<ipaddr> Enter the IP Address.
If there are no additional command keywords or parameters, or if additional parameters
are optional, the following message appears in the output:
<cr> Press Enter to execute the command
You can also enter a question mark (?) after typing one or more characters of a word to
list the available command or parameters that begin with the letters, as shown in the
following example:
(switch) #show m?
mac-addr-table mac-address-table monitor
Ctrl-Y Prints last deleted character
Ctrl-Q Enables serial flow
Ctrl-S Disables serial flow
Ctrl-Z Return to root command prompt
Tab, <SPACE> Command-line completion
Exit Go to next lower command prompt
? List available commands, keywords, or parameters
Table 8. CLI Editing Conventions
Key Sequence Description
- AT8901M CLI Reference Manual 1
- AdvancedTCA 1
- AT8901M Preface 2
- Table of Contents 3
- Table of Contents AT8901M 10
- AT8901M Table of Contents 11
- Appendix 19
- Preface AT8901M 22
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.2.1 Common Parameter Values 29
- 1.5 Command Modes 31
- 1.5.2 CLI Error Messages 34
- 1.6 Using CLI Help 35
- 1.7 Accessing the CLI 36
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8901M 100
- AT8901M Switching Commands 101
- Routing Commands 115
- Chapter 1 115
- 3. Routing Commands 116
- AT8901M Routing Commands 117
- Routing Commands AT8901M 118
- Quality of Service Commands 169
- 4.1.3 classofservice trust 171
- [<slot/port>] 174
- 4.2.1 diffserv 175
- 4.3 DiffServ Class Commands 176
- 4.3.2 class-map rename 177
- 4.3.3 match ethertype 177
- 4.3.4 match any 177
- 4.3.5 match class-map 177
- 4.3.5.1 no match class-map 178
- 4.3.6 match cos 178
- 4.3.7 match secondary-cos 178
- 4.3.9 match dstip 179
- 4.3.10 match dstl4port 179
- 4.3.11 match ip dscp 179
- 4.3.12 match ip precedence 179
- 4.3.13 match ip tos 180
- 4.3.14 match protocol 180
- 4.3.16 match srcip 181
- 4.3.17 match srcl4port 181
- 4.3.18 match vlan 181
- 4.4 DiffServ Policy Commands 182
- 4.4.2 drop 183
- 4.4.3 mirror 183
- 4.4.4 redirect 183
- 4.4.5 conform-color 183
- 4.4.6 class 183
- 4.4.6.1 no class 184
- 4.4.7 mark cos 184
- 4.4.8 mark ip-dscp 184
- 4.4.9 mark ip-precedence 184
- 4.4.10 police-simple 185
- 4.4.11 policy-map 185
- 4.4.11.1 no policy-map 185
- 4.5 DiffServ Service Commands 186
- 4.6 DiffServ Show Commands 187
- 4.6.2 show diffserv 188
- 4.6.3 show policy-map 188
- 4.6.4 show diffserv service 190
- 4.6.7 show service-policy 191
- 4.7.3 {deny 192
- 4.7.4 mac access-group 194
- 4.7.4.1 no mac access-group 194
- 4.7.5 show mac access-lists 194
- 4.8.1 access-list 195
- 4.8.1.1 no access-list 196
- 4.8.2 ip access-group 197
- 4.8.2.1 no ip access-group 197
- 4.8.3 acl-trapflags 197
- 4.8.3.1 no acl-trapflags 197
- 4.8.4 show ip access-lists 197
- 4.8.5 show access-lists 198
- 4.9 ACL trap commands 199
- Utility Commands 201
- 5. Utility Commands 202
- AT8901M Utility Commands 203
- Utility Commands AT8901M 204
- Management Commands 253
- 6. Management Commands 254
- AT8901M Management Commands 255
- Management Commands AT8901M 256
- Getting Help 287
- A. Getting Help 288
- AT8901M Getting Help 289
- Getting Help AT8901M 290
- (if not under warranty) 291
- List of Commands 293
- B. List of Commands 294
- AT8901M List of Commands 295
- List of Commands AT8901M 296
Related products and manuals for Hardware Kontron AT8901M CLI
Hardware Kontron AT8902 User Manual
(94 pages)
(94 pages)
Hardware Kontron AT8902M User Manual
(92 pages)
(92 pages)
Hardware Kontron AT8902M CLI User Manual
(315 pages)
(315 pages)
Hardware Kontron AT8904 User Manual
(93 pages)
(93 pages)
Hardware Kontron AT8904 CLI User Manual
(317 pages)
(317 pages)
Hardware Kontron AT8940 User Manual
(84 pages)
(84 pages)
Hardware Kontron RTM8940 User Manual
(36 pages)
(36 pages)
Hardware Kontron AT8402 CLI User Manual
(253 pages)
(253 pages)
Hardware Kontron AT8404 User Manual
(132 pages)
(132 pages)
Hardware Kontron AT8404 CLI User Manual
(373 pages)
(373 pages)
Hardware Kontron RTM8050 User Manual
(37 pages)
(37 pages)
Hardware Kontron AT8050 User Manual
(165 pages)
(165 pages)
Hardware Kontron RTM8242 User Manual
(34 pages)
(34 pages)
Hardware Kontron AT8242 User Manual
(109 pages)
(109 pages)
Hardware Kontron AT8060 User Manual
(160 pages)
(160 pages)
Hardware Kontron RTM806x User Manual
(40 pages)
(40 pages)
© 2020, manymanuals.com. All rights reserved. | 4.747 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals