Kontron ETX-OH User Manual Page 75
- Page / 100
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
ETX-OH / BIOS Operation
COM0/COM1 Console Redirection Settings
Feature Options Description
Terminal Type VT100
VT100+
VT_UTF8
ANSI
VT100: ASCII char set.
VT100+: Extends VT100 to support color, function keys,
etc.
VT-UTF8: Uses UTF8 encoding to map Unicode chars
onto 1 or more bytes
ANSI: Extended ASCII char set.
Bits per second 9600
19200
38400
57600
115200
Selects serial port transmission speed. The speed must
be matched on the other side. Long or noisy lines may
require lower speeds
Data Bits 7
8
Data Bits
Parity
None
Even
Odd
Mark
Space
A parity bit can be sent with the data bits to detect
some transmission errors. Even: parity bit is 0 if the
num of 1's in the data bits is even. Odd: parity bit is 0 if
num of 1's in the data bits is odd. Mark: parity bit is
always 1. Space: Parity bit is always 0. Mark and Space
Parity do not allow for error detection.
Stop Bits
1
2
Stop Bits indicate the end of a serial data packet. (A
Start bit indicates the beginning). The standard setting
is 1 stop bit. Communication with slow devices may
require more than 1 stop bit.
Flow Control
None
Hardware RTS/CTS
Flow control can prevent data loss from buffer overflow.
When sending data, if the receiving buffers are full, a
'stop' signal can be sent to stop the data flow. Once the
buffers are empty, a 'start' signal can be sent to re-
start the flow. Hardware flow control uses two wires to
send start/stop signals
VT-UTF8 Combo Key Support Disabled
Enabled
Enable VT-UTF8 Combination Key Support for
ANSI/VT100 terminals
Recorder Mode
Disabled
Enabled
With this mode enabled only text will be sent. This is to
capture terminal data.
Resolution 100×31
Disabled
Enabled
Enables or disables extended terminal resolution
Legacy OS Redirection Resolution
80×24
80×25
On Legacy OS, the Number of Rows and Columns
supported redirection
Putty KeyPad
VT100
Linux
XTERMR6
SCO
ESCN
VT400
Select Function Key and KeyPad on Putty
Redirection After BIOS
Always Enable
Boot Loader
If Boot Loader is selected Legacy console redirection is
disabled before booting to legacy OS
75
- Document Revision 130 1
- » Table of Contents « 3
- 1 User Information 5
- 1.5 Warranty 6
- 1.6 Technical Support 6
- 2 Introduction 7
- 3 Specification 8
- 3.2 Functional Specification 9
- Chipset & IOH 10
- Onboard devices 10
- Kontron Features 11
- Power Features 11
- Supported Operating Systems 11
- 3.3 Block Diagram 12
- 3.4 Electrical Specification 13
- 3.5.2 Humidity 14
- WEEE Directive 15
- Conformal Coating 15
- Shock & Vibration 16
- 3.7 MTBF 17
- 3.8 Mechanical Specification 18
- 3.9 Module Dimensions 18
- 3.11 Onboard Connectors 20
- 3.11.2 SATA 21
- 3.11.3 USB 21
- 3.11.4 DisplayPort 21
- 3.11.5 CPU Debug & CPLD 21
- 4 Features and Interfaces 22
- 4.2 S5 Eco Mode 23
- 4.3 M.A.R.S 24
- 4.4 Fast I2C 25
- 4.6 K-Tools 27
- 4.7 K-Station 2 GUI 27
- 4.8 KeAPI 28
- 4.9 Watchdog Timer 29
- 4.10 C-States 30
- 5 System Resources 32
- 5.3 I/O Address Map 33
- 6 ETX® Connectors 34
- ETX-OH / ETX® Connectors 35
- IEC/EN60950 35
- PCI-Bus pins are 5V tolerant 37
- 6.3 Connector X2 (ISA Bus) 38
- 6.4 Connector X4 Subsystems 43
- 7 BIOS Operation 46
- 7.3 Setup Guide 48
- 7.4 POST Codes 48
- 7.5 BIOS Setup 49
- ETX-OH / BIOS Operation 50
- 7.5.2 Advanced 51
- PCI Subsystem Settings 52
- ACPI Settings 53
- Trusted Computing 54
- CPU Configuration 55
- Node 0 Information 56
- Miscellaneous 57
- Watchdog 58
- Smart Battery Configuration 59
- Battery Information 60
- SATA Information 61
- USB Configuration 62
- SMART Settings 63
- Serial Port 0 Configuration 65
- Serial Port 1 Configuration 66
- Parallel Port Configuration 67
- Module H/W Health Monitor 68
- CPU Fan Control 69
- Network Stack 77
- ITE8888 Configuration 78
- Distributed DMA Channel 79
- ISA Decode IO Space 80
- ISA Decode Memory Space 82
- 7.5.3 Chipset 83
- North Bridge 84
- Memory Configuration 85
- Socket 0 Information 86
- South Bridge 88
- SB SATA Configuration 89
- SB USB Configuration 90
- SB LAN Configuration 91
- SB HD Azalia Configuration 92
- 7.5.4 Boot 93
- CSM16 Parameters 94
- CSM Parameters 95
- Add New Boot Option 96
- Delete Boot Option 97
- 7.5.5 Security 98
- 7.5.6 Save & Exit 99
- Corporate Offices 100
Related products and manuals for Hardware Kontron ETX-OH
Hardware Kontron ETX-Starterkit User Manual
(16 pages)
(16 pages)
Hardware Kontron CP3-CMM1 User Manual
(10 pages)
(10 pages)
Hardware Kontron CPCI User Manual
(22 pages)
(22 pages)
Hardware Kontron CP6-BP8-P47-STD User Manual
(12 pages)
(12 pages)
Hardware Kontron CP3-SVE-P200AC User Manual
(10 pages)
(10 pages)
Hardware Kontron CP3-SVE-P200DC User Manual
(10 pages)
(10 pages)
Hardware Kontron CP3-BP8-M-RIO User Manual
(10 pages)
(10 pages)
Hardware Kontron CP3-BP8-P47-RIO User Manual
(12 pages)
(12 pages)
Hardware Kontron CP3-SVE-M100DC User Manual
(12 pages)
(12 pages)
Hardware Kontron CP3-SVE-M76AC User Manual
(10 pages)
(10 pages)
Hardware Kontron CP3-BP4-M User Manual
(8 pages)
(8 pages)
Hardware Kontron CP305 User Manual
(36 pages)
(36 pages)
Hardware Kontron CP6-BP4-PB-RIO User Manual
(10 pages)
(10 pages)
© 2020, manymanuals.com. All rights reserved. | 1.153 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals